(PDF) CIP Level 2 NACE-CIP2-001 Exam and Certification Test Engine
Use NACE-CIP2-001 Exam Dumps (2025 PDF Dumps) To Have Reliable NACE-CIP2-001 Test Engine
NEW QUESTION # 19
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. powder coatings.
- B. urethanes.
- C. inorganic zincs.
- D. epoxies.
Answer: C
NEW QUESTION # 20
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. True
- B. False
Answer: A
NEW QUESTION # 21
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Review the NCR with the other Inspector
- B. Consult your supervisor
- C. Verbally challenge the NCR
- D. Request a re-blast of the item in question
Answer: B
NEW QUESTION # 22
Surface preparation of concrete is performed using:
- A. Methods that are exactly the same as steel
- B. Methods that are completely different to steel
- C. Methods that are the same as wood
- D. Methods that have been modified for concrete
Answer: D
NEW QUESTION # 23
Surface preparation methods for Non-ferrous metals are:
- A. The same as for Ferrous metals
- B. The same for all Non-FetT0us metals
- C. Not required
- D. Specific for each type of Non-ferrous metal
Answer: D
NEW QUESTION # 24
Coating surveys may include which steps?
Select All That Apply:
- A. Schedule the remedial work
- B. Evaluate the coatings performance
- C. Develop a survey plan
- D. Summarize the collected data
Answer: A,B,C,D
NEW QUESTION # 25
Inspection and Test Plans are provided to:
- A. So the Inspector doesn't have to read the entire specification
- B. To supersede the requirements of the product data sheets
- C. So the contractor has a single document to reference
- D. Outline the inspection steps, sequencing and pass/fail criteria
Answer: D
NEW QUESTION # 26
Which is used to calibrate a pH meter?
- A. Distilled water
- B. Standard buffer solution
- C. Deionized water
- D. Standard solvent solution
Answer: B
NEW QUESTION # 27
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. True
- B. False
Answer: A
NEW QUESTION # 28
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Ensure the glue on the dolly is properly applied prior to use
- B. Consult SSPC Guide 1 prior to use
- C. Determine the Dry Film Thickness of the coating prior to use
- D. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
Answer: C
NEW QUESTION # 29
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Don your air supplied respirator and continue the testing
- B. Investigate to find the source of the odor
- C. Exit the tank and document the incident in your daily report
- D. Exit the tank and immediately and report the problem to the nearest safety supervisor
Answer: D
NEW QUESTION # 30
Coating Surveys are legally required:
- A. On water tanks and potable water pipelines
- B. On commercial marine vessels and offshore platforms
- C. On food and beverage vessels and can linings
- D. On high pressure gas lines and fireproofed structures
Answer: B
NEW QUESTION # 31
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise the other inspector he is using an incorrect method
- B. Advise your QC Manager to change the ITP to the use of the salt smart meter
- C. Redo the pre-cleaning based on the other inspectors results
- D. Review the specification with the other inspector to see what method was specified
Answer: D
NEW QUESTION # 32
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. Move the nozzle quicker
- B. a), b) and c)
- C. Lower the blast pressure
- D. Increase the standoff distance
Answer: B
NEW QUESTION # 33
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only in the project would understand
- B. Language that the most would understand
- C. Language that only technical experts would understand
- D. Language that another NACE Inspector would understand
Answer: B
NEW QUESTION # 34
When ASIN D 3363 is specified the Inspector must:
- A. Use the correct solvent
- B. Record the two end points identified in the standard
- C. Record the highest value attained
- D. Record the percentage of failure
Answer: B
NEW QUESTION # 35
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. coatings are expected to degrade over time.
- B. coatings are more durable than linings.
- C. linings are more durable than coatings.
- D. linings protect the contents and the container.
Answer: D
NEW QUESTION # 36
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It contains biocide
- C. It will result in a very slippery surface
- D. It doesn't contain biocide
Answer: B
NEW QUESTION # 37
Dehumidification is defined as the removal of moisture vapor from the air to
- A. lower its temperature
- B. provide worker comfort.
- C. lower its dew point,
- D. raise its relative humidity.
Answer: C
NEW QUESTION # 38
Linings are used on the interior of pipelines to
- A. afford limited temperature insulation.
- B. provide protection against soil chemicals.
- C. reduce magnetic polarity.
- D. protect the transported product.
Answer: D
NEW QUESTION # 39
......
NACE-CIP2-001 Dumps Full Questions with Free PDF Questions to Pass: https://www.braindumpquiz.com/NACE-CIP2-001-exam-material.html
NACE-CIP2-001 PDF Recently Updated Questions Dumps to Improve Exam Score: https://drive.google.com/open?id=1XspF5_1M6SDRPMVX308e1uniDslgDvlP