We're so confident of our products that we provide no hassle product exchange.
H3C GB0-372-ENU Exam Overview:
| Certification Vendor: | H3C |
|---|---|
| Exam Name: | H3CSE-RS-SW Certification Exam (Routing & Switching) |
| Exam Number: | GB0-372-ENU |
| Exam Format: | Multiple response, Multiple choice |
| Available Languages: | English |
| Related Certifications: | H3CIE H3CSE H3CNE |
| Sample Questions: | H3C GB0-372-ENU Sample Questions |
| Exam Way: | Computer-based exam delivered via authorized test centers or online proctoring platforms |
| Pre Condition: | Recommended to have foundational networking knowledge equivalent to H3CNE or similar certification |
H3C GB0-372-ENU Exam Syllabus Topics:
| Section | Objectives |
|---|---|
| IP Routing | - Static routing - BGP fundamentals - OSPF routing protocol |
| QoS and Traffic Management | - QoS concepts and mechanisms |
| Network Fundamentals | - OSI and TCP/IP models - Basic network components and operations |
| Network Services | - DHCP - NAT |
| Network Security Basics | - Basic device security configuration - Access Control Lists (ACL) |
| Ethernet Switching | - Spanning Tree Protocol (STP/RSTP/MSTP) - VLAN configuration and operations - MAC address learning and forwarding |
| IPv4 and IPv6 | - IPv4 addressing and subnetting - IPv6 addressing and deployment |
H3CSE-RS-SW Sample Questions:
VLAN 10 has been created on switch SWA. To use one command to add Ethernet 1/0/1, Ethernet
1/0/2, Ethernet 1/0/3, and Ethernet 1/0/5 ports to VLAN 10, which of the following is correct? (Multiple choice)
- A. [SWA-vlan10] port from Ethernet 1/0/1 to Ethernet 1/0/3 Ethernet1/0/5
- B. [SWA-vlan10] port Ethernet 1/0/1 Ethernet 1/0/2 Ethernet 1/o/3 Ethernet1/0/5
- C. [SWA-vlan10] port Ethernet 1/0/1 to 1/0/3 Ethernet1/0/5
- D. [SWA-vlan10] port Ethernet 1/0/1 to Ethernet 1/0/3 Ethernet1/0/5
Correct Answer: B,D 🗳️
Switches SWA and SWB are connected together through two optical fiber Gigabit Ethernet links, and the following interface configuration is available on switch SWA:
[SWA] interface GigabitEthernet 1/0/1
[SWA-GigabitEthernet1/0/1] gvrp
[SWA-GigabitEthernet1/0/1] port link-type trunk
[SWA-GigabitEthernet1/0/1] port trunk permit vlan 1 10
[SWA] interface GigabitEthernet 1/0/2
[SWA-GigabitEthernet1/0/2] port link-type trunk
[SWA-GigabitEthernet1/0/2] port trunk permit vlan 1 10
If you want to configure link aggregation to aggregate these two links, if the configuration on SWB is correct, which of the following you can know from the above information?
- A. After link aggregation is configured on SWA and SWB, if both SWA and SWB enable MSTP on the aggregation port, one of GigabitEthe1/0/1 and GigabitEthe1/0/2 will be blocked.
- B. After link aggregation is configured on SWA and SWB, if both SWA and SWB enable MSTP on the aggregation ports, GigabitEthernet1/0/1 and GigabitEthe1/0/2 can participate in forwarding.
- C. Only when all VLANs are allowed to pass through GigabitEthernet1/0/2 and Gigabit1/0/1, can the two be added to the same aggregation group.
- D. Only when the configuration of GigabitEthe1/0/2 is changed to be consistent with that of GigabitEthe1/0/1, can the two be added to the same aggregation group.
Correct Answer: B 🗳️
In the network shown in the figure, the interconnection lines between RT1, RT2, RT3 and RT4 are all 1000M links except for the shared Ethernet part which is a 10M link. OSPF protocol is run to make the routes interoperable. The four routers all run PIMSM protocol, and the RP is 1.1.1.1. RT1 and RT2 are connected to receivers on their downstream interfaces, and IGMP is enabled on the corresponding interfaces. Then, when the receiver sends a group join request, which of the following routers have (*, G) entries? (Multiple choice)
- A. RT3
- B. RT2
- C. RT1
- D. RT4
Correct Answer: A,B,C 🗳️
Regarding the spanning tree port cost configuration of H3C switches, which of the following is correct? (Multiple choice)
- A. If switches from different manufacturers are interconnected, the switches should be configured to follow the same port cost standard as much as possible, otherwise the spanning tree calculation results may deviate from the original intention of the network design.
- B. By default, the larger the port cost value, the smaller the port bandwidth
- C. The default spanning tree port cost standard followed by H3C switches is legacy
- D. H3C switches support three port cost standards: dot1d-1998, dot11, and legacy. The stp pathcost- standard command can be used to switch the port cost standard.
Correct Answer: A,B,C,D 🗳️
Which of the following technologies belongs to Layer 3 multicast technology? (Multiple choice)
- A. IGMP
- B. PIM
- C. MVR
- D. IGMPSnooping
Correct Answer: A,B 🗳️
Viewing page 1 out of 87 pages.
Viewing questions 1-5 out of 435 questions.
By Athena
