We're so confident of our products that we provide no hassle product exchange.
HP Deploying HP Enterprise Networks Sample Questions:
1. Click the Exhibit button.
In this star topology, router HKG is the hub. Routers SIN, SGN, and KUL are spokes and are not interconnected. A multicast source at 10.1.1.1 is functioning and able to send streams to all sites. A review of the network shows that PIM DM is configured on all interfaces. All routers are neighbors in OSPF. Receivers 10.2.1.12, 10.3.1.112, and
10.4.1.231 cannot receive the multicast stream, 232.0.0.1.
Which router configuration changes will resolve this issue?
A) [HKG-VLAN-interface100] igmp enable
B) [HKG-pim] static-rp 10.1.254.1 preferred [SIN-pim] static-rp 10.1.254.1 preferred [KUL-pim] static-rp 10.1.254.1 preferred [SGN-pim] static-rp 10.1.254.1 preferred
C) [HKG] c-bsr looback 0 [HKG-pim] c-rp loopback 0
D) [SIN-VLAN-interface200] igmp enable [KUL-VLAN-interface300] igmp enable [SGN-VLAN-interface400] igmp enable
2. In the configuration of a Martini version L2VPN on two PE routers, which parameter must be identical?
A) Service Instance number
B) PW-ID
C) VPN-Target
D) VLAN-ID
E) S-VID
F) Remote LDP Peer IP address
3. You have been asked to configure OSPF on an HP A-Series switch to accomplish the following:
Which set of configuration definitions accomplishes this?
A) ospf 1 router-id 18.1.1.1 passive-interface g1/0/3 area 0 network 0.0.0.0
255.255.255.255
B) ospf 1 router-id 18.1.1.1 silent-interface g1/0/3 area 0 network 0.0.0.0 255.255.255.255
C) ospf 1 router-id 18.1.1.1 silent-interface g1/0/3 area 0 network 255.255.255.255 0.0.0.0
D) ospf 1 router-id 18.1.1.1 passive-interface g1/0/3 area 0 network 255.255.255.255
0.0.0.0
4. Which parameters must be configured on two PE routers to provision an Ethernet L2VPN in Martini mode? (Select four.)
A) L2VPN Address Family
B) Route Distinguisher
C) PW-ID
D) LDP Remote Peer
E) IP Binding
F) Service Instance
G) VPN Instance
H) S-VID
5. Click the Exhibit button.
In this star topology, router HKG is the hub. Routers SIN, SGN, and KUL are spokes and are not interconnected. A multicast source at 10.1.1.1 is functioning and able to send streams to all sites except SIN subnet 10.2.1.0 /24. A review of the network reveals that SIN is able to reach the RP at HKG, loopback 0 10.1.254.1. All routers are neighbors in OSPF. Further, multicast traffic 239.0.0.240 is reaching KUL and SGN receivers, but not the receiver at 10.2.1.12.
Which commands best diagnosis the problem as a multicast issue?
A) [SIN] display pim routing-table [SIN] display saved-configuration [SIN] display pim join-prune mode sm
B) [SIN] display pim routing-table [SIN] display multicast boundary [SIN] display pim rp-info
C) [SIN] display pim routing-table [SIN] display multicast boundary [SIN] display pim bsr-info
D) [SIN] display pim routing-table [SIN] display pim interface [SIN] display pim bsr-info
E) [SIN] display ip routing-table [SIN] display pim interface [SIN] display pim bsr-info
Solutions:
| Question # 1 Answer: D | Question # 2 Answer: B | Question # 3 Answer: B | Question # 4 Answer: C,D,F,H | Question # 5 Answer: B |
By Ellen
